Accurate liquid flow for building services and industrial water.

The D116 is designed for high-speed, accurate liquid flow measurement across various pipe materials.

See specifications Request a Quote

At a glance

What D116 does, in plain words.

What it measures: Liquid flow; How much liquid moves through the pipe.
How it installs: Clamp-on; Sensors fit on the outside of the pipe, so the pipe stays closed.
How it connects: RS485 / 4–20 mA; Wired into control systems over Modbus RS485, or as a 4–20 mA signal.
Pipe sizes: DN25–DN1200; DN is the nominal pipe size, roughly the inside diameter in millimetres.

Why D116

D116 in short.

The D116 is designed for high-speed, accurate liquid flow measurement across various pipe materials. With stable signals and a user-friendly setup, it provides reliable data tracking for building services and industrial water management, with consistent performance and minimal maintenance.

Where it is used

HVAC
Process industries
Energy management and environmental monitoring
Agriculture and irrigation systems
Facilities management
Industrial maintenance and troubleshooting

D116 · 2026 product catalog

How it works

Sound with the flow arrives sooner.

Two sensors on the same side of the pipe take turns sending sound through the water. Sound travelling with the flow arrives slightly sooner than sound travelling against it; the meter turns that time difference into flow, which is why it needs to know your pipe.

How clamp-on ultrasonic measurement works →

Pipe & installation

What the meter needs to know about your pipe.

These are set up on the meter after installation. Pipe size and transducer type are decided when ordering.

Pipe & installation guide pipe materials, sizes, setup checklist

Stainless steel · 2″ example

A smooth metal surface. Clean the spot, add coupling gel, then clamp the sensor on.

60.3mmacross the outside

2.8mmwall thickness

54.8mmacross the inside

Pipe sizes are names, not measurements: a 2″ pipe is 2.375″ across.

The meter needs Pipe size Wall thickness Material: Stainless steel

Technical details standards, OD / ID, both units

Standard: ASME B36.19 · 2″ Sch 10S
Outside diameter (OD): 2.375″ (60.33 mm)
Wall: 0.109″ (2.77 mm)
Inside diameter (ID): 2.157″ (54.79 mm)
Meter parameters: OD · wall · material

This guide shows what a clamp-on meter needs to know about a pipe. It does not mean every model fits every pipe: check the specifications below or ask an engineer.

Specifications

Check the fit before you specify.

The short version is above. These are the specifications published for D116; values that are still being checked are left out.

Performance

Flow velocity: 0.01–5.0 m/s (0.03–16 ft/s)
Pipe size: 25–1200 mm (1″–48″)
Accuracy: ±1% of reading (0.5–5 m/s)
Repeatability: 0.2%
Pipe material: Carbon steel, stainless steel, copper, PVC

Function

Communication: RS485 with Modbus protocol
Analogue output: 4–20 mA, max. load 750 Ω
Pulse output: 0–9999 Hz, OCT, adjustable frequency limits
Relay output: Max. 1 Hz, 1 A at 125 VAC or 2 A at 30 VDC
Power supply: 10–36 VDC, 1 A max.

Physical

Ambient temperature: −10 °C to 50 °C (14 °F to 122 °F)
Transducer temperature: 0 °C to 80 °C (32 °F to 176 °F)
Ingress protection: Transmitter IP65, transducer IP68
Transducer cable: 9 m (29.5 ft) standard

Need a value that is not listed, or the datasheet for your configuration? Ask an engineer.

What these terms mean

DN: Nominal pipe size, roughly the inside diameter in millimetres (DN50 ≈ 50 mm).
Clamp-on: Sensors strap to the outside of the pipe. No cutting, no shutdown for installation.
PoE: Power over Ethernet: one network cable carries power and data.
LoRaWAN: Long-range, low-power wireless. Readings travel through a gateway to a network server.
Modbus RS485: A wired connection widely used by building and industrial control systems.
4–20 mA: An analogue signal where the current represents the reading.