F3P · Fixed flow

Panel transmitter. Remote clamp-on sensors.

A flow meter with a panel-mounted transmitter and separate clamp-on sensors for DN20–DN80 pipes. Power and data run over one PoE network cable.

See specifications Request a Quote

At a glance

What F3P does, in plain words.

What it measures: Liquid flow; How much liquid moves through the pipe.
How it installs: Clamp-on; Sensors fit on the outside of the pipe, so the pipe stays closed.
How it connects: PoE / Ethernet; One Ethernet cable carries both power and data.; Works with MeterTube, the pFlow app and cloud platform.
Pipe sizes: DN20–DN80; DN is the nominal pipe size, roughly the inside diameter in millimetres.

Why F3P

F3P in short.

F3P measures liquid flow with a panel-mounted transmitter and separate clamp-on sensors, using the transit-time ultrasonic principle. Installation needs no contact with the liquid and no shutdown.

Power and network data share one PoE cable. Readings go to the cloud, where you can view and manage them in the mobile app or on the web.

Connect one network cable and start measuring
Power over Ethernet (PoE)
Online updates and upgrades
Live data in the mobile app and on the web

Where it is used

Flow control and monitoring
Totalised flow
Water distribution

Wall-mounted F3P transmitter with a PoE switch

How it works

Sound with the flow arrives sooner.

Two sensors on the same side of the pipe take turns sending sound through the water. Sound travelling with the flow arrives slightly sooner than sound travelling against it; the meter turns that time difference into flow, which is why it needs to know your pipe.

How clamp-on ultrasonic measurement works →

Pipe & installation

What the meter needs to know about your pipe.

These are set up on the meter after installation. Pipe size and transducer type are decided when ordering.

Pipe & installation guide pipe materials, sizes, setup checklist

Stainless steel · 2″ example

A smooth metal surface. Clean the spot, add coupling gel, then clamp the sensor on.

60.3mmacross the outside

2.8mmwall thickness

54.8mmacross the inside

Pipe sizes are names, not measurements: a 2″ pipe is 2.375″ across.

The meter needs Pipe size Wall thickness Material: Stainless steel

Technical details standards, OD / ID, both units

Standard: ASME B36.19 · 2″ Sch 10S
Outside diameter (OD): 2.375″ (60.33 mm)
Wall: 0.109″ (2.77 mm)
Inside diameter (ID): 2.157″ (54.79 mm)
Meter parameters: OD · wall · material

This guide shows what a clamp-on meter needs to know about a pipe. It does not mean every model fits every pipe: check the specifications below or ask an engineer.

Specifications

Check the fit before you specify.

The short version is above. These are the specifications published for F3P; values that are still being checked are left out.

Performance

Flow velocity: 0.03–5.0 m/s (0.1–16 ft/s)
Pipe sizes: DN20, DN25, DN32, DN40, DN50, DN65, DN80
Accuracy: ±2% of reading (0.3–5 m/s)
Repeatability: 0.2%
Pipe material: Carbon steel, stainless steel, PVC, copper

Function

Network: Ethernet with Power over Ethernet (PoE)
Power supply: Power over Ethernet (PoE), IEEE 802.3af/at

Physical

Ambient temperature: −10 °C to 50 °C (14 °F to 122 °F)
Transducer temperature: 0 °C to 60 °C (32 °F to 140 °F)
Ingress protection: IP54
Transducer cable: Sensor cable 9 m (29.5 ft); PoE network cable 2 m (6.6 ft)

Need a value that is not listed, or the datasheet for your configuration? Ask an engineer.

What these terms mean

DN: Nominal pipe size, roughly the inside diameter in millimetres (DN50 ≈ 50 mm).
Clamp-on: Sensors strap to the outside of the pipe. No cutting, no shutdown for installation.
PoE: Power over Ethernet: one network cable carries power and data.
LoRaWAN: Long-range, low-power wireless. Readings travel through a gateway to a network server.
Modbus RS485: A wired connection widely used by building and industrial control systems.
4–20 mA: An analogue signal where the current represents the reading.